# 2D_heat_transfer_MATLAB2

Budget ₹2200-3000 INR

- Freelancer
- Jobs
- Engineering
- 2D_heat_transfer_MATLAB2

An industrial mixer stirs fluid inside a rectangular vessel. One side of the vessel is heated. The flow can be

approximated as two dimensional and the configuration is shown in figure 1.

When the mixer is started, the fluid has an initial temperature of T(x, y, t = 0) = y through the domain,

where y is the vertical location. At time t0 = 0 (s), the mixer begins to rotate the fluid inside the vessel.

You are required to determine the temperature of the fluid at location x = 0.5 m and y = 0.25 m at time

t = t0 + 1 s and also determine the final steady state temperature (as time goes to infinity) at this same

location. This problem can be treated as two dimensional and the length and height of the domain are

L = 1 m. The fluid has thermal diffusivity of α = 0.1 [m2/s].

[

\

/

/

7\ \ 7\ \

7

7

8[\

9[\

Figure 1: Solution Domain with thermal boundary conditions

The assignment is arranged into two parts:

In Part A you will obtain a steady solution to the heat equation for this problem using a second order

accurate finite difference scheme and an iterative solver. Your goal is to obtain the solutions (T(x, y)) on a

range of mesh sizes and use these solutions to estimate the exact value of temperature at location (x = 0.5 m,

y = 0.25 m ).

In Part B you will obtain a transient solution to the heat equation for this problem using a first order

implicit finite difference discretisation in time. The goal is to report the temperature at location (x = 0.5 ,

y = 0.25) at time t = 1 s using a number of grid sizes and time steps sizes and estimate the exact solution.

You will present your results for each part in a short report. In this report you must briefly explain your

method, the discrete equations solved, how boundary conditions were applied, explain what simulations

were performed and how you determined your solution is accurate. Details for each section are given in the

following pages.

steps

Discretise the governing equation and boundary conditions with second order accurate centered finite difference approximations. Use Matlab to write an iterative solver to solve the governing equation (1) to find

the temperature. You should follow the steps below and then present your method, solution and accuracy

tests in a short report.

1. Discretise the governing equations and boundary conditions using a second order accurate centered

finite difference scheme.

2. Write a Matlab code to solve the discrete set of equations using the Gauss-Seidel SOR method. Set a

stopping criterion for the solver (any of the methods given in the notes are fine).

3. You might like to play around with the relaxation factor ω to find a value that seems optimal (you

don’t need to report on these tests). An optimal value is one that attains a solution in as few iterations

as possible. The optimal value may vary with grid size.

4. Vary the grid size so ∆x = ∆y = L/2

n where n = 3, 4.... Demonstrate the accuracy of your scheme

by monitoring the T at (x, y) = (0.5, 0.25). Choose an appropriate stopping criterion for the solver for

each grid size.

5. Determine the grid size for which the solution is asymptotic, then estimate the exact solution accurate

to 6 significant figures. Note: Ensure you store your results to a large number of significant figures

and make sure your stopping criterion is small enough.

6. Using the above results write a short ∼ 3 page report presenting your solution T(x, y) and in particular

the result T(x = 0.5, y = 0.25). You must explain what mesh size and convergence criterion you used.

You are to clearly demonstrate to the reader that your solution is accurate. You should briefly present

your numerical method including the final discrete equations you solve. Your report should explain

how you ensured your final solution was accurate and refer to the sources of error in your calculations

## 5 freelancers are bidding on average ₹3630 for this job

Hi, I hope you are doing fine. I have PhD in mechanical engineering from Tohoku University of Japan. I have published 20 Journal papers and 16 international conference papers. I have a lot of experience in automotive, More

Am a Mechatronic engineer with 5 year experience in my field and I believe i can handle your task to perfection

Hi, there, I 'm a matlab expert and have 10+ years of experiences. I have good experiences in several heat transfer projects. I'll provide you quality work according your instructions. Please award me the project so th More

I have over 5 years of expertise with Matlab, Simulink and reports based on the same. I also have knowledge in Image processing, Communications, Wireless Electrical Engineering and other related subjects. I can also d More

I am a MATLAB-MBD( Model Based Development) developer and will solve this MATLAB problem in 3 days.